Draytek Vigor 2960 Firmware v1.0.9, SSL VPN效能大幅提升10倍 ~ 10/30/2014

本帖最後由 idolclub 於 2014-10-30 01:46 編輯

Release Note for Vigor2960
Firmware Version: 1.0.9
Release Date: October 24, 2014
Applied Models: Vigor2960, Vigor2960F

************************************************************************************
Due to the firmware size limitation, for devices using firmware version 1.0.5 or earlier, it is
suggested to upgrade to firmware version 1.0.7.1 first before upgrading to version 1.0.9 or later.
************************************************************************************

New Features
* Improve SSL VPN performance for tunnel mode (with Smart VPN Client 4.3.1 or later, the throughput will be greater than 200Mbps)
* Support USB 4G/LTE. Check USB>>Modem support list for details
* Support USB disk /FTP server.
* Support Policy Route (integrating original Load Balance Rule and Address Mapping).

Improvement
* Corrected: CPE didn’t check authenticated from VigorACS SI.
* Corrected: Can't establish IPv6 static connection.
* Improved: Allow to pass/block NetBios packets through IPSec VPN tunnel.
* Improved: Allow downloading/ uploading private key (for Host to LAN VPN by X.509).
* Improved: Show the VPN Type/Form fields on VPN History web page.
* Improved: Handle Duplicated Routes (with Static Route Metric). When static route metric is smaller or equals to 10, the priority of static route will be greater that VPN route.
* Improved: Support QoS for VoIP traffic from LAN.
* Improved: Support "Ping to Keep Alive" feature for detecting IPsec tunnel is alive or not.
* Improved: Support WAN Port and IP Alias options for PPTP Dial Out connection.
* Improved: Support RFC 4638(accommodating a MTU/MRU Greater Than 1492 in the PPPoE).
* Improved: Add STUN server option to TR-069 settings.
* Improved: Add Jumbo Frame to edit Maximum Frame size.
* Improved: Support saving Syslog to USB disk.
* Improved: Add the "Clear" button for DDNS settings page.
* Improved: Support to import/export Bind IP to MAC.
* Improved: Support Allow Ping from the specified WAN.
* Improved: Add “OVH” as service provider for DDNS setting.
* Improved: Support Range-to-many Port Redirection.
* Improved: Improve login page customization for Web Portal setup.
* Improved: Change mechanism of deleting objects.
* Improved: Upgrade OpenSSL to 0.9.8zc for SSLv3 Fallback protection.

Known Issue
* You need to disable "Force IPsec with L2TP" options for pure L2TP tunnel in VPN and Remote Access >> PPP General Setup.



Download:

"Due to the firmware size limitation, for devices using firmware version 1.0.5 or earlier, it is suggested to upgrade to firmware version 1.0.7 first before upgrading to version 1.0.8.x."

http://www.draytek.com/index.php ... p;lang=en#downloads

聽日鴨腳upgrade試下先

TOP

啱啱download完update唔到.

upload完個firmware去router後,verify時出"invalid firmware file" error.

file係V2960_1.0.9_r4394.all

TOP

啱啱download完update唔到.

upload完個firmware去router後,verify時出"invalid firmware file" error.

f ...
bereavement 發表於 2014-10-30 09:12

現在用緊邊一個firmware版本?  如何升級?

TOP

現在用緊邊一個firmware版本?  如何升級?
idolclub 發表於 2014-10-30 11:42



    1.0.8.2
係web gui upgrade firmware

TOP

1.0.8.2
係web gui upgrade firmware
bereavement 發表於 2014-10-30 11:54

先Reboot router,再重新下載firmware,關閉電腦防毒及防火牆軟件再升級

TOP

先Reboot router,再重新下載firmware,關閉電腦防毒及防火牆軟件再升級
idolclub 發表於 2014-10-30 12:01



    攪掂!原來因Chrome問題。用IE update OK咗。立即試下SSL VPN有冇快
咗先.Thanks師兄

TOP

試咗SSL VPN throughput高咗, 但latency都係明顯比PPTP/L2TP/IPSec高.但都有明顯進步

WebGUI 都有好多嘢唔同咗
1. status 果度而家係會見到D燈閃
2. Load Balance Pool/Policy Routing搬咗落 routing個tab
3. Inbound load balance而家獨立左。放喺WAN個tab
4. USB application多咗function
5. Nat Session table 詳細易睇左.


同埋CPU loading好似低咗.

TOP

想問下各位如果更新完Firmware用不用LOAD返出廠設定之後再SET過定係佢更新完後D設定會KEEP返而且唔會引致有D小問題出現?

TOP



CPU用量大幅下降.
1.0.8.2時idle都用30幾%CPU(開咗QoS, Firewall)


1.0.9下都係開咗QoS同Firewall.都係幾% idle.
附件: 您需要登錄才可以下載或查看附件。沒有帳號?註冊

TOP