[操作疑難] tp link wr940n 2.0刷錯firmware 5.0版本 怎救?

入到主畫面

擦唔到dd wrt

又擦唔返2.0

有冇方法?

提示: 作者被禁止或刪除 內容自動屏蔽

TOP

睇下tp link有冇軟件係for recovery
冇ge, 有個軟件(tXXX)係for 所有router recovery,直接放個rom入去 ...
sorryman 發表於 2015-4-22 19:20




唔係好明

TOP

tftp??

TOP

提示: 作者被禁止或刪除 內容自動屏蔽

TOP

tftp??
c2600264 發表於 2015-4-22 22:50



    Want to (re)install the firmware on a TPlink device using the TFTP method.

Do this:

Note: ensure that you have upgraded to latest stock firmware before continuing

1) Press the WPS/Reset button during power up a couple of times until the star light starts to blink really fast.

If it doesn't, then power off the box and start again. This will make bootstrap loader enter the TFTP recovery mode. The procedure can be used to transfer a firmware image.

2) Assign 192.168.0.66 to your local network interface (the router uses 192.168.0.86) and connect your laptop/pc to one of the LAN ports of the TP-Link.

3) Download tftp32 if your are using windows here http://tftpd32.jounin.net/download/Tftpd32-4.50-setup.exe

(If you have another operating system let us know)

4) Rename the PolkaSpots firmware which was provided to wdr4300v1_tp_recovery.bin

(If you need this, please visit mywifi.polkaspots.com/firmwares

5) Publish that file on your TFTP server and fire the server up on the ethernet interface.

6) Wait for the firmware to be transferred. In the case it doesn't start, step 1 will need to be repeated.

Please make sure your box has been added to CT. This should install things nicely.

Good luck!

------------------------------------------------------------

請問應該點做

TOP

1)按電源了幾次,直到星光在WPS/ Reset按鈕開始閃爍非常快。如果沒有,則關閉該框並再次啟動。這將使引導加載程序進入TFTP恢復模式。該過程可以被用來傳送一個固件映像。

2)分配192.168.0.66到本地網絡接口依個點set?(路由器使用192.168.0.86)和你的筆記本電腦/ PC連接到的TP-LINK的LAN端口中的一個。

TOP

試左tftp 個軟件唔識郁

http://service.tp-link.com.cn/detail_article_2197.html



以上圖中識郁

點解我裝左唔識郁

TOP

試左tftp 個軟件唔識郁





以上圖中識郁

點解我裝左唔識郁
wahaha118 發表於 2015-4-23 14:38


你電腦的網絡卡目前IP可能位於不同網絡, 試下手動設定為192.168.0.66(我估192.168.0.x 都可以)
以Win7為例, 在"控制台\網路和網際網路\網路和共用中心"裡面的 "區域連線\內容\網際網路通訊協定第四版TCP/IP v4" 內容, "使用下列的IP位址,IP位置填上192.168.0.x, 子網路遮罩填上255.255.255.0"
然後再開tftp試下

TOP