又有一些問題想問..

大家好, 上次問完Heaksink D野, 今次又想問下各位Ching一D問題關於Pc Case同其他Water-cooling零件. 由於我從來未玩過水冷, 所以請多多指教.
1. 我今次第一次, 可能只想試下水冷 cpu, graphics card and North, south bridge. 請問Single loop會唔會太少? 定要double loop?
2. 請問水冷係唔係要heat sink, pump, radiator, tubing and reservoir以上東西? 如有錯誤, 請Ching指點.
3. Plate Heat exchanger (http://www.koolance.com/water-cooling/default.php?cPath=54_119)同Radiator有冇分別? 好似radiator有fan, 而plate exchanger冇? 
4. 我有個Cooler Master Cosmos 1000(http://www.coolermaster.com/product.php?product_id=6600). 請問可唔可以將一套水冷放入去? 要唔要Mod case? 因為我唔係太想expose D零件.
希望大家可以答到我D問題.
Thanks! 

本帖最後由 k2t4 於 2010-1-22 09:16 編輯
又有一些問題想問..
大家好, 上次問完Heaksink D野, 今次又想問下各位Ching一D問題關於Pc Case同其他Water-cooling零件. 由於我從來未玩過水冷, 所以請多多指教.
1. 我今次第一次, 可能只想試下水冷 cpu, graphics card and North, south bridge. 請問Single loop會唔會太少? 定要double loop?
2. 請問水冷係唔係要heat sink, pump, radiator, tubing and reservoir以上東西? 如有錯誤, 請Ching指點.
3. Plate Heat exchanger (http://www.koolance.com/water-cooling/default.php?cPath=54_119)同Radiator有冇分別? 好似radiator有fan, 而plate exchanger冇?
4. 我有個Cooler Master Cosmos 1000(http://www.coolermaster.com/product.php?product_id=6600). 請問可唔可以將一套水冷放入去? 要唔要Mod case? 因為我唔係太想expose D零件.
希望大家可以答到我D問題.
Thanks!  


Overclocker 發表於 2010-1-22 08:22


1. 水冷 cpu, graphics card and North, south bridge. 最好double loop
    第一次 唔好 玩咁大, 玩住 cpu , north and south bridge 行 Single loop 先啦
2. 水冷 係要 block, pump, radiator, tubing and reservoir ,    heat sink 係風冷零件
3. Plate Heat exchanger 無 fan , 係 passive 被動式散熱 ; radiator 有 fan ,  係 active 主動式散熱
4. Cooler Master Cosmos 1000 可以將一套水冷放入去
    搜尋 " Cooler Master Cosmos 1000 + water-cool " 會找到好多例子

TOP

我睇到D圖, 見到人地個pump放在PSU右面, 不過CM Cosmos 1000個intake fan不就是剛剛在那個為致?!(即係唔用?) 如果我Graphics card 唔玩水, 敢味好難散熱?

Sorry, 我仲想想問下D野.
1. 個reservior要幾大?要裝係邊先好?
2. 有無2 fan radiator 介紹, 而可以裝在個case上面out-take fan個位置?
3. D5 pump 可唔可以handle double loop? 定要兩個? 

TOP

本帖最後由 k2t4 於 2010-1-23 12:05 編輯
我睇到D圖, 見到人地個pump放在PSU右面, 不過CM Cosmos 1000個intake fan不就是剛剛在那個為致?!(即係唔用?) 如果我Graphics card 唔玩水, 敢味好難散熱?

Sorry, 我仲想想問下D野.
1. 個reservior要幾大?要裝係邊先好?
2. 有無2 fan radiator 介紹, 而可以裝在個case上面out-take fan個位置?
3. D5 pump 可唔可以handle double loop? 定要兩個?
Overclocker 發表於 2010-1-23 01:40


1. 個 reservior 唔洗好大 , 部份玩家 什至會用 T-Line 代替
      一般裝在水泵 入水口 附近 , 什至與水泵 連為一體

2. 2 fan radiator 可以裝在個case上面out-take fan個位置
    2 fan radiator -- 240 (12cm fan x 2 ) or 280 (14cm fan x 2 ) radiator
    Black ICE GTX240 or GTX280   

3. one loop one pump

TOP

提示: 作者被禁止或刪除 內容自動屏蔽

TOP

Sorry, I am at my friend's house, cannot type Chinese.....
1.What is T-Line? Where do you put it? Can you describe it a bit more?
2. I see that the Black ICE GTX240 is very thick, over 50mm. How much better will be it compared to one that is 32 cm thick?
3. How fast should the fans on the Radiators be? like 1800RPM?

TOP

提示: 作者被禁止或刪除 內容自動屏蔽

TOP

回復 6# Overclocker
1. The T joint is placed before the pump, this is where you do all your filling and airing in the WC loop, same purpose as a reservoir. Comparing with a proper reservoir the "T" gives you more internal space but not as convineient as a reservoir.

2. There are lots of revirews online and some forums.

3. Depends on the density of the fin. You can usually see these numbers on the specs, look for the FPI (fins per inch) value. Just remember the higher density the radiator fin has, the more air pressure it needs to push/pull through it. Hope it makes sense.

TOP

1. 個 reservior 唔洗好大 , 部份玩家 什至會用 T-Line 代替
      一般裝在水泵 入水口 附近 , 什至與水 ...
k2t4 發表於 2010-1-23 10:05


我上網睇過, 見到 D人話Thermochill PA 120.2 radiator好好, 雖然佢成60mm厚, 不過無 Black ice GtX 240 (53mm) 禁貴, why? 雙方又有咩大分別? 你地覺得邊個好D?

我成日有D唔明咩係tubing的ID, OD 同 fitting thread. 其實真正個意思係咩? 各位Ching可唔可以又解釋下?

TOP

本帖最後由 k2t4 於 2010-1-24 11:23 編輯
我上網睇過, 見到 D人話Thermochill PA 120.2 radiator好好, 雖然佢成60mm厚, 不過無 Black ice GtX 240 (53mm) 禁貴, why? 雙方又有咩大分別? 你地覺得邊個好D?

我成日有D唔明咩係tubing的ID, OD 同 fitting thread. 其實真正個意思係咩? 各位Ching可唔可以又解釋下?
Overclocker 發表於 2010-1-24 08:25


Thermochill PA 120.2 radiator好好, 雖然佢成60mm厚, 不過無 Black ice GtX 240 (53mm) 禁貴
你是否睇錯 貸幣單位 ??
Thermochill PA 120.2       HKD$1280.00         
Black ice GTX 240            HKD$780.00

咩係 tubing 的 ID , OD -- 水喉的呎吋
ID -- Inner Diameter (內徑)
OD -- Outer Diameter (外徑)
一般使用 :
12x16 = 12mm 內徑 , 16mm 外徑 , 一般叫 4分 ( 1/2 吋 ) 喉

fitting thread -- 接頭 的 牙規
一般使用 :
G1/4 =  2分 喉管通用牙 , 大約等於10.5mm 直徑

TOP