Updating OCZ Vertex 1.5 firmware

係咪所有firmware都可以直接up做1.5?

唔係,出廠時或自行更新上左firmware1.42既Vertex唔可以用呢個更新,等一下佢會再出另一版firmware

TOP

唔係,出廠時或自行更新上左firmware1.42既Vertex唔可以用呢個更新,等一下佢會再出另一版firmware ...
yohoman0000 發表於 31/1/2010 04:31 AM

咁如果我係1.2, 1.3呢?

TOP

回復 3# lai_tsz_ho

當然可以啦,早2日我先由1.3 up左上去 1.5,佢個algorithm真係好左,速度有5-10MB/s左右既提升,而且HDTune benchmark時條線穩定左好多,冇上下跳動得太多
其實如果你有懷疑,可以上ocz forum睇下什至問下,有好多資料睇,你問既問題佢個firmware download post有講
http://www.ocztechnologyforum.co ... EX-drives-and-Turbo
1.5 FW update for Agility, Vertex, EX drives, and Turbo

    Do not use the files in this post for Turbo, use the files in Post #4

    Do not use the files in this post for a drive on FW 1.42, start at post #6.

    Do not flash backwards from 1.5 to 1.4/1.41/1.3/1.1.

    Same rules as the 1.4 updaters, this works in IDE mode only (you can't be in AHCI), on Macs detection is slow...so be patient....

TOP

本帖最後由 lai_tsz_ho 於 2010-1-31 12:59 編輯

回復 4# yohoman0000

係咪要o係BIOS set左做IDE, flash完再set番做AHCI裝windows?
定係IDE mode就得?

TOP

回復 5# lai_tsz_ho

唔明你個point,你指全新安裝window?
如果你已經用緊,就直接up上去,佢唔會洗你d野,你怕有問題就Backup 先
Update firmware一定要用IDE mode,而且IDE mode先係vertex work得最好既模式,用IDE mode就唔洗理係咪AHCI

TOP

本帖最後由 lai_tsz_ho 於 2010-1-31 22:56 編輯

回復 6# yohoman0000

哦, 姐係IDE run得仲好, 咁我揀IDE黎run啦 (新機)
係唔係揀左IDE就好難轉AHCI?

TOP

回復 7# lai_tsz_ho

你用XP? 如果你未來可能會玩AHCI或RAID,最好就o係安裝Windows時搞定先,因為遲d想用先搞幾煩,但肯定唔會用就唔洗理
如果你用vista或win7,就直接o係安裝時先在BIOS轉AHCI再安裝Windows,裝完再轉回IDE,XP做唔到呢樣野,因為冇driver而且強行轉會BSOD,要用floppy碟搞,睇你需要

TOP

回復 8# yohoman0000

我用Win 7
咁姐係Vista同Win 7都可以裝左Windows再轉? Thx!

TOP

我用 Windows7 , 裝時AHCI mode , 但之後轉 IDE 就會藍晝面,
另我upgrade左 1.5後 , write speed 都係得 95MB/s.
係唔係因為我用 INTEL ICH9 呢?
1.5 有冇分 GC/non GC 版架?

TOP