標題: Makibox 終於到手^^ [打印本頁]

---

作者: wc1984    時間: 2014-3-23 17:19     標題: Makibox 終於到手^^

本帖最後由 wc1984 於 2014-3-23 17:21 編輯

新手一名~ 當玩具買左部機玩下~


整左三個鐘定好~ 當然SET 下print 下LA~


食完飯返黎見到 print 好^^ 勁開心


我覺得算唔錯了~


左係第一次 右係第三次


對我黎講~ 第一次print 到野真係好好好好開心^^

圖片附件: photo 1.JPG (2014-3-23 17:20, 44.76 KB) / 下載次數 23
https://www.hkepc.com/forum/attachment.php?aid=1652759&k=10cd4283d327903601eafe83f7fc937c&t=1781969571&sid=tbqVkCGZm



圖片附件: photo 2.JPG (2014-3-23 17:20, 46.06 KB) / 下載次數 49
https://www.hkepc.com/forum/attachment.php?aid=1652760&k=1d913c66f9ca78c93a6a0229cd3fd267&t=1781969571&sid=tbqVkCGZm



圖片附件: photo 3.JPG (2014-3-23 17:20, 52.25 KB) / 下載次數 20
https://www.hkepc.com/forum/attachment.php?aid=1652761&k=f69b7138c82d1c7376e0b6b83eca7835&t=1781969571&sid=tbqVkCGZm



圖片附件: photo 4.JPG (2014-3-23 17:20, 42.43 KB) / 下載次數 19
https://www.hkepc.com/forum/attachment.php?aid=1652762&k=16bd0aa43103adfde61d2288be69a2af&t=1781969571&sid=tbqVkCGZm



圖片附件: photo 5.JPG (2014-3-23 17:20, 25.1 KB) / 下載次數 34
https://www.hkepc.com/forum/attachment.php?aid=1652763&k=2e718723ee3ddac610e4c40bc302535f&t=1781969571&sid=tbqVkCGZm

---

作者: henryvii99    時間: 2014-3-23 17:40

先恭喜你成功駕馭到MAKIBOX

我相信版上的師兄們會比你一個更專業嘅評估
不過係我眼中你呢個盒都叫四四方方

似乎MAKIBOX的表現都幾飄忽

三個用家三部機三個盒
由完全噴唔完,到不似盒形, 到失步失到變棱形,
到你呢個 (我相信你呢個係MAKIBOX用家中, 現時為止最靚一個)

我倒想問問版上師兄意見, 點解廠機質素可以差咁遠

無論點都好, 再恭喜樓主PRINT到件自己滿意嘅作品

---

作者: wc1984    時間: 2014-3-23 17:53

我覺得佢youtube 教學幾有用呀~
我睇住佢黎整 睇住佢黎SET
搞最耐反而係個software! 佢個 5D print 已經用唔到了!!!!!
現在用緊 Repetier

仲有佢果個放膠座已無用~ 完全不能好好上膠~ 用左佢個paper box 改一改仲好^^


實在忍唔住手~ 未set 好都print 住先!!!!!


圖片附件: photo 1.JPG (2014-3-23 17:52, 46.65 KB) / 下載次數 35
https://www.hkepc.com/forum/attachment.php?aid=1652772&k=ba43d9a3cf0538827b78bd919150ac75&t=1781969571&sid=tbqVkCGZm



圖片附件: photo 2.JPG (2014-3-23 17:52, 47.27 KB) / 下載次數 63
https://www.hkepc.com/forum/attachment.php?aid=1652773&k=5d7f31b580bfaec13bdc62092c925ead&t=1781969571&sid=tbqVkCGZm

---

作者: Super169    時間: 2014-3-23 17:56



Makibox 係成品定係要自己砌既?

如果成品既話....又真係........(無言)
如果印到咁 (我估你係想印四方磚掛), 我可能又會出 post 求救了.  
不過 ching 好似一次比一次好 (部機有自我修補功能 ), 都算好彩, 希望 ching 唔會好似我咁黑仔啦.

---

作者: wc1984    時間: 2014-3-23 18:27

Makibox 應該全部係kit 無成品呀?~
一次比一比好 係因為每次都tune 一tune 先印~ 所以咪可以一次好過一次~^^

---

作者: Super169    時間: 2014-3-23 21:35




oic,  唔好意思, 小弟唔識野.
希望 ching 早日 tune 機完成, 印多 D 好野比我地睇.

---

作者: azraelho    時間: 2014-3-23 23:04

恭喜師兄一次搞掂
師兄可唔可以分享下你個setting? 你用咩切片software?

---

作者: wc1984    時間: 2014-3-23 23:52

本帖最後由 wc1984 於 2014-3-23 23:54 編輯

我用Repetier + Slic3r
you can try my setting in Slic3r

avoid_crossing_perimeters = 0
bed_size = 110,150
bed_temperature = 110
bottom_solid_layers = 4
bridge_acceleration = 0
bridge_fan_speed = 100
bridge_flow_ratio = 1
bridge_speed = 50
brim_width = 0
complete_objects = 0
cooling = 1
default_acceleration = 0
disable_fan_first_layers = 1
duplicate = 1
duplicate_distance = 6
duplicate_grid = 1,1
end_gcode = M104 S0 ; turn off hot end\nM140 S0 ; turn off hot bed\nG92 E0 ; set E value to 0 at current position\nG1 F1000 X0 Y0 E-15 ; 1000mm/min speed of print head, 15mm filament to retract\nG92 E0 ; set E value to 0 at current position\nM84 ; disable motors
external_perimeter_speed = 40
external_perimeters_first = 0
extra_perimeters = 1
extruder_clearance_height = 20
extruder_clearance_radius = 20
extruder_offset = 0x0
extrusion_axis = E
extrusion_multiplier = 1
extrusion_width = 0
fan_always_on = 0
fan_below_layer_time = 60
filament_diameter = 1.75
fill_angle = 45
fill_density = 0.3
fill_pattern = rectilinear
first_layer_bed_temperature = 120
first_layer_extrusion_width = 200%
first_layer_height = .3
first_layer_speed = 20
first_layer_temperature = 235
g0 = 0
gap_fill_speed = 25
gcode_arcs = 0
gcode_comments = 0
gcode_flavor = reprap
infill_acceleration = 0
infill_every_layers = 1
infill_extruder = 1
infill_extrusion_width = 0
infill_first = 0
infill_only_where_needed = 0
infill_speed = 50
layer_gcode =
layer_height = .1
max_fan_speed = 100
min_fan_speed = 35
min_print_speed = 17
min_skirt_length = 15
notes =
nozzle_diameter = 0.4
only_retract_when_crossing_perimeters = 1
output_filename_format = [input_filename_base].gcode
perimeter_acceleration = 0
perimeter_extruder = 1
perimeter_extrusion_width = 0
perimeter_speed = 40
perimeters = 2
post_process =
print_center = 55,75
raft_layers = 0
randomize_start = 0
resolution = 0
retract_before_travel = 2
retract_layer_change =
retract_length = 3
retract_length_toolchange = 10
retract_lift = 0
retract_restart_extra = 0
retract_restart_extra_toolchange = 0
retract_speed = 70
rotate = 0
scale = 1
skirt_distance = 4
skirt_height = 1
skirts = 2
slowdown_below_layer_time = 30
small_perimeter_speed = 35
solid_fill_pattern = rectilinear
solid_infill_below_area = 70
solid_infill_every_layers = 0
solid_infill_extrusion_width = 0
solid_infill_speed = 50
spiral_vase = 0
start_gcode = G28 ; home all axes\nM109 S[first_layer_temperature] ; heat up hot end to set temperature\nM82 ; use absolute distances for extrusion\nG90 ; use absolute coordinates\nG92 E0 ; set E value to 0 at current position\nG1 F500 E35 ; 500mm/min speed of print head, 35mm filament to extrude\nG92 E0 ; set E value to 0 at current position
support_material = 0
support_material_angle = 0
support_material_enforce_layers = 0
support_material_extruder = 1
support_material_extrusion_width = 0
support_material_interface_layers = 0
support_material_interface_spacing = 0
support_material_pattern = rectilinear
support_material_spacing = 2.5
support_material_speed = 45
support_material_threshold = 0
temperature = 235
threads = 2
toolchange_gcode =
top_infill_extrusion_width = 0
top_solid_infill_speed = 40
top_solid_layers = 10
travel_speed = 55
use_relative_e_distances = 0
vibration_limit = 0
wipe = 0
z_offset = 0