標題: [測試] 試畫Delta Laser Cut [打印本頁]

---

作者: bunbunlui    時間: 2014-4-22 20:06     標題: 試畫Delta Laser Cut

將Delta既列印件轉左做Lasercut件, 俾冇printer又想自己砌既師兄DIY
唔知有冇野畫漏


圖片附件: Delta Laser Cut V1 (re-arrange).jpg (2014-4-22 20:06, 133.81 KB) / 下載次數 85
https://www.hkepc.com/forum/attachment.php?aid=1665552&k=44f428354ca7bcbb615814c6f839dfe4&t=1781958747&sid=8yAkktZLF

---

作者: 789456123    時間: 2014-4-22 20:30

支持 ,雖然睇唔明.

---

作者: bunbunlui    時間: 2014-4-22 20:44


個Design係for 2020鋁型材加6mm光軸, 加埋上面幅圖應該易明D

圖片附件: Delta Laser Cut V1 Construction.jpg (2014-4-22 20:43, 130.27 KB) / 下載次數 71
https://www.hkepc.com/forum/attachment.php?aid=1665565&k=a63195e4c535a4763de4125e9afc3124&t=1781958747&sid=8yAkktZLF

---

作者: secmaster    時間: 2014-4-22 20:54

有冇成品圖?

---

作者: bunbunlui    時間: 2014-4-22 21:39

未有, 只係今日畫出黎

---

作者: hktvro    時間: 2014-4-22 21:53

正想整部Kossel玩玩 ,支持樓主無私分享 , 加油 !

---

作者: ptawong    時間: 2014-4-22 22:14




    原本8mm光軸,可能不夠,現改10mm板本
http://www.thingiverse.com/thing:154832

---

作者: secmaster    時間: 2014-4-23 09:06

回覆 7# ptawong


    我砌嗰部木頭都係8mm

---

作者: bunbunlui    時間: 2014-4-24 18:23

本帖最後由 bunbunlui 於 2014-4-24 18:24 編輯

師兄8mm唔夠既意思係唔夠精度定係唔穩陣?
6mm唔夠既話要睇下點改10mm


圖片附件: Delta Laser Cut V1 (measure).jpg (2014-4-24 18:22, 138.29 KB) / 下載次數 95
https://www.hkepc.com/forum/attachment.php?aid=1666120&k=b0e38ae115014fa1574a9d833551a9c4&t=1781958747&sid=8yAkktZLF

---

作者: ptawong    時間: 2014-4-24 18:57

FYI--

UPDATE: 01/02/2014
As it was noticed by Senormeow http://www.ohmpie.com/delta_printer/, the 8mm rods are not sturdy enough for this height. I will be uploading stl files for 10mm rods version soon which should help to make it more rigid. If you decide to use 8mm rods anyway then I would advice to use shorter extrusion lengths for the columns or lower top frame by 10-20cm. Bear in mind it's still work in progress ;), thanks

---

作者: bunbunlui    時間: 2014-4-24 20:22

IC, 佢部機成800咁高, 所以易彎, 我諗砌500用8mm應該冇問題

---

作者: secmaster    時間: 2014-4-24 21:45

我部木頭機50cm 高, 都係用8mm光軸

---

作者: prof2034    時間: 2014-4-30 23:48

我想問吓你個圖紙係JPG, 係唔係唔可以直接攞去比人LASER CUT.

---

作者: bunbunlui    時間: 2014-5-1 00:05

jpg唔得，會有誤差，要用返ai，corel 嗰d畫圖檔至得
個圖仲係構思中，唔知界出黎work唔work，如果師兄有興趣，我畫完後再放上黎

---

作者: Offer    時間: 2014-5-1 06:45




   
我部木頭機TOM, 係用10mm光軸

---

作者: bunbunlui    時間: 2014-5-2 18:57


畫完, 用8mm光軸

圖片附件: Delta Laser Cut V2 (re-arrange).jpg (2014-5-2 18:56, 147.75 KB) / 下載次數 53
https://www.hkepc.com/forum/attachment.php?aid=1669150&k=b4af4603db67f2eb9e628dcff509f0e6&t=1781958747&sid=8yAkktZLF