電子門鎖密碼重設方法

本帖最後由 KKKK 於 2010-4-26 13:57 編輯

請問這類密碼門鎖的更改密碼的方法是怎樣的? (只講密碼,沒有 RFID﹗)

Please have a look at this :

RFID Access Control System CU-K05 User's Manual

1. Brief Product Introduction:
This product provides access control mode, which is safe and fully automatic, it is an ideal device for business organizations, offices, factories, residences and communities.

2. Setup:
Default value: Login password 9999 , User password 1234

Enter programming mode:
Press * Login password # enter programming mode.

Function setup (while in programming mode):

1). Modify login password.
Press 0 new password # confirm new password # (Note: the new password should be 4-8 digits.)

2). Add user card.
Press 1 read card Card location # (Note: the Card location should be three digits from 001 to 250, which should not duplicate. The Card location must be input, otherwise the card will be invalid. If add more than one cards, read the second card directly after the Card location is input before pressing # .

3). Delete user card (three ways):

    * Press 2 0000 # to delete all user cards.
    * Press 2 read card # to delete the corresponding card
    * Press 2 Card location # to delete lost card.

4) Set open mode:

    * Press 3 00 # by valid card only.
    * Press 3 01 # by valid card and password.
    * Press 3 02 # by valid card or password.
      Note: factory setting is valid card. Since the initial password can not be used to open door, If set to valid card or password mode, password for user should be modified.

5) Set user password
Press 5 new user password # repeat user password # (Note: new user password should be 4-6 digits)

6) Save the settings and exit programming mode:
Press * (Note: should be pressed within 1 minute to save the setting when any of the above operation is completed.)

3. How to use:
Depending on the open mode, can be open by valid card, card + user password or user password only.
However, if in card + password mode, the user password should be input with one second after card swiping.

If program password is forgotten, you can use jumper switch RESET at the main board to restore factory setting.

    * First, power off. Then set jumper switch to ON position. Power on. System beeps 3 times
    * Power off then set jumper back to OFF position. now the factory setting is restored.

TOP

最直接用十字螺丝批1支,搞掂

TOP

回復 2# tnovicet

Thanks for your reply. Actually I'm not talking about this model but I would like to know this type of password lock (without RFID).

Anyway, may be some of the part from your information might applicable.

Thanks!

TOP

回復 3# rossi_lao

十字螺絲批1支?點搞?

TOP

本帖最後由 rossi_lao 於 2010-4-27 13:15 編輯

个壳底有螺丝,拆开后找到锁线(非法用途唔好话我讲嘎

TOP

本帖最後由 rossi_lao 於 2010-4-27 13:15 編輯

个壳底有螺丝,拆开后找到锁线(非法用途唔好话我讲嘎
重复咗

TOP

回復 7# rossi_lao

重复咗

TOP

回復 6# rossi_lao


我係要改密碼喎﹗依個電子密碼鎖,見人地改密碼都唔洗開底壳?

TOP

找到了類似的 Manual 了﹗ 謝謝兩位回覆的 師兄﹗

TOP