3K

我返而想用N16 SET做ss client , 又可以support DDNS 同 Multi SS Server
之前用openwrt 做client 一定要入IP

upi

回覆 8# 蠢貓


AC68U 喺arm cpu, 裝entware-ng的方法好似會同 mipsr2 router 有點不同?
https://gist.github.com/dreamcat4/6e58639288c1a1716b85
quoted from  github:
"Instructions for ARM device

mount a disk to '/tmp/mnt/usb_hdd' or similar. Do not use the internal 'JFFS' flash, it will kill / ruin your router"

arm cpu router 可否把entware-ng / optware 裝到jffs flash上, 請上網爬吓文先去馬

AC68U都可以裝tomato shibby: http://tomato.groov.pl/?page_id=69

tomato shibby 已內建entware package, 可直接install entware 及 opkg update / install entware package

upi

回覆 10# mcdull

tomato shibby 喺用entware-ng, 我未試過裝到optware
反而係dd-wrt router 裝到optware + openconnect server, 不過entware/optware 都係用opkg update / install

    喺tomato shibby 的 router admin page 有web gui 比admin 加入start up / firewall script, 唔駛自已用putty 入router etc/init.d 自己打startup script, dd-wrt router 都有得喺admin web gui 加 command script, 這些方便一般用家的web gui我諗一般3rd party firmware 都會有吧?

至於merlin router係咪冇web gui要好似linux 咁用putty 入command line自已set startup script小弟就不太清楚了.

gameplayer

幾個月前post過, 不過沉咗落深海, 見近嚟多人問點搞shadowsock, 又撈返上嚟另外開新貼比各位ching參考吓.

...
upi 發表於 2017-4-29 22:25

CHING,我跟住以上steps setup 左，但不能連接，而又不知道邊一步出錯。
CHING ，請問如果查看ss-server 是否在router 啟動時已一拼開啟？

蠢貓

回覆  蠢貓


AC68U 喺arm cpu, 裝entware-ng的方法好似會同 mipsr2 router 有點不同?

quoted from  git ...
upi 發表於 2017-5-4 11:02

唔該師兄提點，睇嚟都係要用ext2 or 3嘅usb去裝
我部68u係c1版，所以冇得裝tomato，前日tomato出咗更新版但依然都冇c1嘅68u

upi

回覆 14# gameplayer


    你裝好jffs, mount jffs/opt to opt, entware-ng, opkg install shadowsock 後, 有冇setup好init script /firewall script?

測試方法可以直入putty command line, 去opt/bin run ss-server -c /opt/etc/shadowsocks.json -v 行verbose mode, 睇吓個ss-server有冇start

after make sure ss-server is working, 先至係init script 加入ss-server -c /opt/etc/shadowsocks.json

好多時係path 錯(i.e.冇mount jffs/opt to opt), encrypt method錯, config json 打錯字, firewall rule / iptable 冇正確setup 之類搞到ss-server不能啟動

upi

回覆 15# 蠢貓


    咁個flash咁Q多位咪得個擺字?

蠢貓

回覆 17# upi
我都覺得好浪費。。。
但用usb嘅話，一嚟要format做ext2/3，做transmission嘅話寫入速度及穩定低，二來兩個usb ports一早已滿
以前用tomato有內置transmission好滿意，換新router都冇留意merlin嘅rom係點

gameplayer

回覆  gameplayer


    你裝好jffs, mount jffs/opt to opt, entware-ng, opkg install shadowsock 後,  ...
upi 發表於 2017-5-4 17:28

Check 過幾次，暫時未搵到問題系邊？
“測試方法可以直入putty command line, 去opt/bin run ss-server -c /opt/etc/shadowsocks.json -v 行verbose mode, 睇吓個ss-server有冇start”
Ching,我來到這裡（下圖），請問系putty 要打咪 command check 到 ss-server 個狀態?(PS:小弟都command不熟，見諒）

upi

回覆 19# gameplayer

entware 個ss-server D command 同linux版唔同, 冇start喱個command, ss-server -h for help

putty 入router
cd /opt/bin
ss-server -c /opt/etc/shadowsocks.json -v

然後去用手機之類試吓能否連到ss-server, 如果連線失敗, 睇吓個router putty screen 同client app出D乜

ss-server command 解說:
-c = use config file
shadowsocks.json 就係個config file
/opt/etc/ 就係個config file的位置
-v = verbose mode