[Centos 7]yum mysql 404

本帖最後由 DrERY 於 2017-1-19 17:39 編輯

本身想裝mysql 5.6, 點之404................點處理????

[root@server01 ~]# wget  http://repo.mysql.com/mysql-community-release-el7-5.noa                                                                                     rch.rpm
--2017-01-19 16:58:31--  http://repo.mysql.com/mysql-community-release-el7-5.noa                                                                                     rch.rpm
Resolving repo.mysql.com (repo.mysql.com)... 23.219.134.205
Connecting to repo.mysql.com (repo.mysql.com)|23.219.134.205|:80... connected.
HTTP request sent, awaiting response... 200 OK
Length: 6140 (6.0K) [application/x-redhat-package-manager]
Saving to: ‘mysql-community-release-el7-5.noarch.rpm’

100%[======================================>] 6,140    --.-K/s in 0s

2017-01-19 16:58:31 (53.3 MB/s) - ‘mysql-community-release-el7-5.noarch.rpm’ sav                                                                                     ed [6140/6140]

[root@server01 ~]# rpm -ivh mysql-community-release-el7-5.noarch.rpm
Preparing...                         ################################# [100%]
Updating / installing...
1:mysql-community-release-el7-5 ################################# [100%]
[root@server01 ~]# yum install mysql-server
Loaded plugins: fastestmirror
http://repo.mysql.com/yum/mysql- ... hfp/repodata/repomd                                                                                     .xml: [Errno 14] HTTP Error 404 - Not Found
Trying other mirror.
To address this issue please refer to the below knowledge base article

https://access.redhat.com/articles/1320623

If above article doesn't help to resolve this issue please create a bug on https                                                                                     ://bugs.centos.org/

One of the configured repositories failed (MySQL Connectors Community),
and yum doesn't have enough cached data to continue. At this point the only
safe thing yum can do is fail. There are a few ways to work "fix" this:

   1. Contact the upstream for the repository and get them to fix the problem.

   2. Reconfigure the baseurl/etc. for the repository, to point to a working
      upstream. This is most often useful if you are using a newer
      distribution release than is supported by the repository (and the
      packages for the previous distribution release still work).

   3. Run the command with the repository temporarily disabled
         yum --disablerepo=mysql-connectors-community ...

   4. Disable the repository permanently, so yum won't use it by default. Yum
      will then just ignore the repository until you permanently enable it
      again or use --enablerepo for temporary usage:

         yum-config-manager --disable mysql-connectors-community
      or
         subscription-manager repos --disable=mysql-connectors-community

   5. Configure the failing repository to be skipped, if it is unavailable.
      Note that yum will try to contact the repo. when it runs most commands,
      so will have to try and fail each time (and thus. yum will be be much
      slower). If it is a very temporary problem though, this is often a nice
      compromise:

         yum-config-manager --save --setopt=mysql-connectors-community.skip_i                                                                                     f_unavailable=true

failure: repodata/repomd.xml from mysql-connectors-community: [Errno 256] No mor                                                                                     e mirrors to try.
http://repo.mysql.com/yum/mysql- ... hfp/repodata/repomd                                                                                     .xml: [Errno 14] HTTP Error 404 - Not Found