MartinChiu

Check 下 Z probe 有無接錯正負極。
個人經驗
palpatrick 發表於 2015-12-22 16:51

    無，因為一路正常印緊野，我無搞過硬件～

MartinChiu

SENDING:G1 X0 Y0 Z0
>>> M114
SENDING:M114
X:0.00 Y:0.00 Z:0.00 E:0.00 Count X: 187.62 Y:187.62 Z:187.62

MartinChiu

好怪唔係0

dtom

貼返個 M503 睇睇先

MartinChiu

貼返個 M503 睇睇先
dtom 發表於 2015-12-22 17:38

>>> M503
SENDING:M503
echo:Steps per unit:
echo:  M92 X100.00 Y100.00 Z100.00 E150.00
echo:Maximum feedrates (mm/s):
echo:  M203 X200.00 Y200.00 Z200.00 E200.00
echo:Maximum Acceleration (mm/s2):
echo:  M201 X3000 Y3000 Z3000 E3000
echo:Acceleration: S=acceleration, T=retract acceleration
echo:  M204 S3000.00 T3000.00
echo:Advanced variables: S=Min feedrate (mm/s), T=Min travel feedrate (mm/s), B=minimum segment time (ms), X=maximum XY jerk (mm/s),  Z=maximum Z jerk (mm/s),  E=maximum E jerk (mm/s)
echo:  M205 S0.00 T0.00 B20000 X20.00 Z20.00 E20.00
echo:Home offset (mm):
echo:  M206 X0.00 Y0.00 Z0.00
echo:Endstop adjustement (mm):
echo:  M666 X0.00 Y0.00 Z0.00
echo:PID settings:
echo:   M301 P22.20 I1.08 D114.00

vichui

回覆 12# MartinChiu

1. Firmware 有冇著#define EEPROM_SETTINGS，　冇著就唔洗理Ｍ50X果埋野， 有就
     upload fw -> m502 -> m503(睇清楚d數字，冇問題的話)－> M500
2. Endstop 亂左, 用M119 check 下d endstop有冇trigger到（可以能endstop 壞左）
3. check Z_PROBE_OFFSET_FROM_EXTRUDER , 電感／servo多數用-， 直接印頭就＋

vvserpent

睇CONFIG , enable EPROM 果行, 而家係REMARK 左.   
//#define EEPROM_SETTINGS

你有冇試過RESET 部機? 試下RESET 佢.

另外,  打入 M666 L , 對下 Z-HEIGHT 同 FIRMWARE 入面SET 既有冇分別.

MartinChiu

start
Printer is now online.
echo:Marlin1.0.0
echo: Last Updated: Dec 22 2015 18:58:49 | Author: (MICROMAKE KOSSEL)
Compiled: Dec 22 2015
echo: Free Memory: 3628  PlannerBufferBytes: 1232
echo:Hardcoded Default Settings Loaded
echo:Steps per unit:
echo:  M92 X100.00 Y100.00 Z100.00 E150.00
echo:Maximum feedrates (mm/s):
echo:  M203 X200.00 Y200.00 Z200.00 E200.00
echo:Maximum Acceleration (mm/s2):
echo:  M201 X3000 Y3000 Z3000 E3000
echo:Acceleration: S=acceleration, T=retract acceleration
echo:  M204 S3000.00 T3000.00
echo:Advanced variables: S=Min feedrate (mm/s), T=Min travel feedrate (mm/s), B=minimum segment time (ms), X=maximum XY jerk (mm/s),  Z=maximum Z jerk (mm/s),  E=maximum E jerk (mm/s)
echo:  M205 S0.00 T0.00 B20000 X20.00 Z20.00 E20.00
echo:Home offset (mm):
echo:  M206 X0.00 Y0.00 Z0.00
echo:Endstop adjustement (mm):
echo:  M666 X0.00 Y0.00 Z0.00
echo:PID settings:
echo:   M301 P22.20 I1.08 D114.00
echo:SD card ok

dtom

M665 先係 Z-HEIGHT
M666 係 Endstop offset

MartinChiu

So Sad
i also ask micromake CS
but can not help >_<