tracer44

對的，是這樣。想問一下排線是HDMI線定其他線問題？我見到師兄有啲買果條有啲boost signal有小小唔明問題在哪裡。唔好意思問咁多，但一買番來print唔到實在有啲煩氣

alancck

對的，是這樣。想問一下排線是HDMI線定其他線問題？我見到師兄有啲買果條有啲boost signal有小小唔明問題在 ...
tracer44 發表於 2017/12/14 23:39

boost signal  應該係用 root 權限去改 raspberry pi ，你依家嗰問題應該係啲線插唔好...或者係張卡嗰插頭位鬆咗...又或者係offer大大講FCP排線扣唔實/移咗位...試下抆晒啲線再插過，或者問人借線，自己買條hdmi線試下...不過如果aryau師兄可以分享下點攪返好就多一個參考囉...

tracer44

ok今晚番去試下. 因為我試過dry run 冇事,點知來真又唔得.
另外想問下各大大會唔會清潔個PLATFORM? 定由佢滴乾算?

Offer

ok今晚番去試下. 因為我試過dry run 冇事,點知來真又唔得.
另外想問下各大大會唔會清潔個PLATFORM? 定由佢 ...
tracer44 發表於 2017-12-15 17:28

唔會清潔個PLATFORM

tracer44

今晚終於print到了那粒正方形。但用酒精洗完後啲邊位發白，請問是否正常？另外我只用兩層base但print完會彎，是咪加多兩層底層就可避免？
而家print緊雀籠但要朝早先有得睇。謝謝

alancck

今晚終於print到了那粒正方形。但用酒精洗完後啲邊位發白，請問是否正常？另外我只用兩層base但print完會彎 ...
tracer44 發表於 2017/12/16 01:36

恭喜晒喎，請問可唔可以分享下點攪點嘅呢？可以俾下次遇到相同問題嘅師兄作為一個參考哦...發白應該係因為洒精未乾得晒就進行2次固化...

tracer44

其實冇攪過啲咩,just moved the machine such that the HDMI cable is not being tensioned or compressed, and slightly moved the HDMI connectors at the machine so it connects better. Same cable everything remains the same.

I left the machine on to print the bird cage last night. But then the print failed, and now the machine OLED is gone and i cannot connect back to the machine again.
Is it likely that the Rasberry Pi burnt?

vvserpent

其實冇攪過啲咩,just moved the machine such that the HDMI cable is not being tensioned or compressed, ...
tracer44 發表於 2017-12-16 10:56

塊PI 應該好易試到, HDMI 接MONITOR 有冇OUTPUT ?  會唔會係火牛問題?  SD CARD 死左?
希望你快D 搞好, 有得玩啦.

tracer44

師兄想問下點試塊PI?我完全控制唔到部機所以試唔到個monitor. 我想試下邊樣壞但又唔識試。

tracer44

相當奇怪, 今日開機又佢又開到. 但print job前用唔到printer control. 要calibrate 要用手.
換了另一隻resin味小左好多,但深色左,所以試print church 失敗了.
又唔記得清缸差啲爆mon.
之前print 正方型個邊有層文是否正常?

下載 (70.27 KB)

2017-12-17 23:18