原帖由 K_C_ 於 2009-6-24 01:01 AM 發表
I am not going to start fighting with anybody, according to ACARD's spec, the max transfer rate is 400MB/s, but is that possible under a SATA 2.0 interface?

And when we are talking about "ma ...

Since ACARD's spec, the max transfer rate is 400MB/s, but the max transfer rate of DD2-RAM is much more higher than that, in other words, it is ACARD's problem to limit the transfer rate, it cannot fully utilize the fast transfer rate of DDR2-RAM. Bearing in mind that it is a RAM drive, it should be much more faster than any SSD, but in fact, ACARD has not done so.

TOP

原帖由 fastloopattack 於 2009-6-24 01:32 發表

Since ACARD's spec, the max transfer rate is 400MB/s, but the max transfer rate of DD2-RAM is much more higher than that, in other words, it is ACARD's problem to limit the transfer rate, it cannot f ...


No, sure NOT.

No matter what component inside the ACARD, SSD, HDD or whatever, the interface is still SATA 2.0. It is hence limited to 3.0Gb/s, in theory, that's 300MB/s only.

TOP

原帖由 tyranid 於 2009-6-24 12:23 AM 發表

Wow, what a impressive 435.78MB/s sequential read by 3Ware RAID controller and 4x ACARD in RAID5. It is twice as fast as a single SSD in sequential read  , and almost 10 times slower than a single SS ...

Actually it is in 8-ports RAID5, so, ACARD is too slow since we are using DDR2-RAM which should have very fast transfer rate of several GB/s, but it even cannot break the 1GB/s barrier.

TOP

原帖由 K_C_ 於 2009-6-24 01:35 AM 發表


No, sure NOT.

No matter what component inside the ACARD, SSD, HDD or whatever, the interface is still SATA 2.0. It is hence limited to 3.0Gb/s, in theory, that's 300MB/s only.

But I am not using a single SATA2 interface. I am using 8-ports RAID5 array, the transfer rate should be at least over 1GB/s.

TOP

You might be able to reach 1+GB/s by 2 controllers in RAID(Adaptec 5805 or ARECA 1680), let each of them carry 4 ports

TOP

原帖由 輕基黃 於 2009-6-22 15:47 發表


There are two possible limitations:
1. 3Ware 9650SE is PCI-E x 4
2. Acard Drive's memory speed controller cannot utilize the full speed of DDR2-800 ram
Theoretically, the full speed of DDR2-800 ram  ...


3Ware 9650SE is PCI-e x 4???

As what I found, it should be x 8? Link

"PCI Express x1, x4, x8 configurations, PCI Express 1.1 compliant"

TOP

And here is a further example, adding more SSDs to a RAID card may not has linear or even positive results.

Link

So there may not have a RAID card which is 100% "compatible" with the SSDs right now.

TOP

原帖由 K_C_ 於 2009-6-24 09:22 發表


3Ware 9650SE is PCI-e x 4???

As what I found, it should be x 8? Link

"PCI Express x1, x4, x8 configurations, PCI Express 1.1 compliant"

According to your provided link, it is clear that for 8-ports, 3Ware 9650SE is PCI-E x4.

TOP

原帖由 輕基黃 於 2009-6-24 09:34 發表

According to your provided link, it is clear that for 8-ports, 3Ware 9650SE is PCI-E x4.


Oh yes...... sorry I mixed up.

So theoretically, the max transfer rate for 9650SE is 1GB/s. And now you have around 60% efficiency, which is marginally acceptable.

TOP

原帖由 K_C_ 於 2009-6-24 09:26 發表
And here is a further example, adding more SSDs to a RAID card may not has linear or even positive results.

Link

So there may not have a RAID card which is 100% "compatible" with the SSDs ri ...


Then what was used in the SSD RAID we saw in the YouTube video?
(I don't remember exactly but there was a YouTube video showing a team building a SSD RAID with a huge number of SSDs...)

TOP