lianli v1000 新春大裝修

denden

新年到，同大家拜個早年先。前幾日出完差翻到屋企，之前訂個批貨已到，跟手就一連3日對舊機進行全面裝修。目標系打機時可以達到delta 10度內。

配置：
mb：asus m4e
cpu：2500k oc 4.6g@1.26v
display：gtx580 3g oc 930@1.1v
ram：3星金條16g
hd disk：intel g3 160g + 3.5 inch hdd x 2

新裝修後wc配置：
rad：pa120.2， ex120， ex360
cpu：ek hf
vga： ek
fans： sanyo 9s x 5
res+pump：koolance rp-402 x 2，ddc 18w x 2 w/koolance heatsink 行一條loop
coolant：屈銀紙
喉：r-3603 3分喉

lamptron fc5

下載 (128.61 KB)
要放360排只可以機頂開孔

2012-1-20 02:18

下載 (94.1 KB)
機底放pa120.2

2012-1-20 02:20

下載 (97.58 KB)
res連2個ddc

2012-1-20 02:20

下載 (119.5 KB)
檯面亂到9彩

2012-1-20 02:20

下載 (90.48 KB)
唔系改機箱呢世都唔會買既工具

2012-1-20 02:20

下載 (88.05 KB)
上好ek hf，造工一流

2012-1-20 02:20

下載 (109.52 KB)

2012-1-20 02:20

下載 (83.25 KB)
電磨用來先定位

2012-1-20 02:20

下載 (74.58 KB)
連工具一齊買幾standley工具箱

2012-1-20 02:20

下載 (129.09 KB)
3個rad

2012-1-20 02:20

下載 (89.02 KB)
開好曬孔，對好位上到rad，邊打磨，水洗，烘乾ing

2012-1-20 02:20

下載 (100.03 KB)
烘乾中

2012-1-20 02:20

下載 (111.26 KB)
二樓先鋪carpets

2012-1-20 02:20

下載 (102.88 KB)
鋪完效果唔錯

2012-1-20 02:20

下載 (113.41 KB)
機底開始上pa120.2

2012-1-20 02:20

下載 (123.87 KB)
機底開始上pa120.2

2012-1-20 02:21

下載 (73.12 KB)
機底開始上pa120.2

2012-1-20 02:21

下載 (99.2 KB)
fit位

2012-1-20 02:21

下載 (116.76 KB)
舒服曬

2012-1-20 02:21

下載 (108.23 KB)
mb上3喉

2012-1-20 02:21

下載 (113.16 KB)
mb先上機先可以裝其餘2個rad

2012-1-20 02:21

下載 (115.1 KB)
話咁快就上埋其餘2個rad

2012-1-20 02:21

下載 (105.38 KB)
特寫

2012-1-20 02:21

下載 (142.41 KB)
特寫

2012-1-20 02:21

下載 (126.52 KB)
機頂rad上買彎頭

2012-1-20 02:21

下載 (80.6 KB)

2012-1-20 02:21

下載 (95.18 KB)
第二日繼續幫1樓鋪地毯

2012-1-20 02:21

下載 (100.66 KB)
機側板都鋪埋，但吸音效果無乜

2012-1-20 02:21

下載 (90.32 KB)
繼續駁喉

2012-1-20 02:21

下載 (96.56 KB)
繼續駁喉

2012-1-20 02:21

下載 (132.09 KB)
mcw60 拜拜啦

2012-1-20 02:21

下載 (120.9 KB)

2012-1-20 02:21

下載 (73.8 KB)
580 slot板超難鬆，因為上左螺絲膠，扭到滑曬牙，只可以用電磨硬爆

2012-1-20 02:21

下載 (124.54 KB)
喉上曬，準備試水，我發覺宜家用compression fitting基本唔使點試，唔似以前。只要喉切得平嘴扭得緊就唔會 ...

2012-1-20 02:21

下載 (75.72 KB)
最痛苦既駁線過程，細機箱我又想線靚又唔想包線，只可以用extension cable，走左我成晚先合得埋側板 ... ...

2012-1-20 02:21

下載 (113.77 KB)

2012-1-20 02:21

下載 (108.47 KB)
新居入伙啦！yeah！

2012-1-20 02:22

下載 (97.7 KB)

2012-1-20 02:21

下載 (116.13 KB)
overall look，下一步會打磨前面塊鋁板，鏡面bling bling

2012-1-20 02:21

同以前比水溫好靚，fans speed 1000，idle delta 3度，bf3 delta 8度，張580爆99%都系43度，超滿意

hgcjeffrey

正, VGA換埋Full Cover添,
原來EX 薄排都有咁既威力.

c-hing識貨喎, ↓我都有↓

下載 (62.13 KB)

2012-1-20 04:19

(5D Mark II 35.4L.....眼紅中...)

Overclocker

回復 3# hgcjeffrey


    Is that ram heatsink?..0.0

Overclocker

回復 1# denden


    Where can I buy those sound proof mats? Did it come in one large piece and you cut them into smaller pieces yourself?

melody20541

好靚 好有心機整.....
到我唔知會整D咩出黎

0011ss22

pump 1 出直入 pump 2?

denden

回復 3# hgcjeffrey

都系唔好浪費姐！ex series perform as good as rx series according to data sheet but its much slimmer

denden

回復 4# Overclocker

its actually ramsink from 亨利 ram wc block， I dislike its block so I just reuse its heatsink, u can search by the name akasa in tb, it comes with 4 pcs, 2 large 2 smaller for 2 sides, floor and ceiling I guess

denden

回復 7# 0011ss22

why not? its easilier for routing in my case, and that hole is placed lower than the offically recommended setting so there's more water to drain when needed to replace coolant, reroute or replace parts.

performance wise, it seems as strong as the offical settings even though I dont have the meter......will add in later